LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Ford >> 2002 >> Crown Victoria Base, 4.6 9 >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 3 (Engine Controls - System & Component Tests - EEC-V - Gasoline) >> Evaporative Emission System Tests >> Hissing Sound When Removing Fuel Cap >> Escort, Escort ZX2 & Focus

Escort, Escort ZX2 & Focus

WARNING: This page is about a different variant/trim than selected.
  1. Testing EVAP Canister & Canister Vent Solenoid Flow -  Connect Evaporative Emissions System Leak Tester (134-00056) to test port. Pressurize system to 14 in. H2 O (3.48 kPa). If pressure drops immediately, EVAP canister and vent solenoid are not blocked, go to step  5. If pressure does not drop immediately, go to next step.

  2. Testing Canister Vent Solenoid Hose Assembly

    Disconnect canister vent solenoid hose assembly. Pressurize system to 14 in. H2 O (3.48 kPa). If pressure drops immediately, replace canister vent solenoid hose assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform DRIVE CYCLE PROCEDURE under DIAGNOSTIC MONITORS in SELF-DIAGNOSTICS - EEC-V - GASOLINE & NGV article. Ensure PENDING CODE CHECK & EVAP MONITOR "BYPASS" CHECK is performed. If pressure does not drop immediately, go to next step.

  3. Testing Canister Vent Solenoid For Blockage

    Remove canister vent solenoid. Pressurize system to 14 in. H2 O (3.48 kPa). If pressure drops immediately, replace canister vent solenoid. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform DRIVE CYCLE PROCEDURE under DIAGNOSTIC MONITORS in SELF-DIAGNOSTICS - EEC-V - GASOLINE & NGV article. Ensure PENDING CODE CHECK & EVAP MONITOR "BYPASS" CHECK is performed. If pressure does not drop immediately, go to next step.

  4. Testing EVAP Canister

    Disconnect EVAP canister tube at canister. Pressurize system to 14 in. H2 O (3.48 kPa). If pressure drops immediately, replace EVAP canister. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform DRIVE CYCLE PROCEDURE under DIAGNOSTIC MONITORS in SELF-DIAGNOSTICS - EEC-V - GASOLINE & NGV article. Ensure PENDING CODE CHECK & EVAP MONITOR "BYPASS" CHECK is performed. If pressure does not drop immediately, replace EVAP canister outlet tube. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform DRIVE CYCLE PROCEDURE under DIAGNOSTIC MONITORS in SELF-DIAGNOSTICS - EEC-V - GASOLINE & NGV article. Ensure PENDING CODE CHECK & EVAP MONITOR "BYPASS" CHECK is performed.

  5. Testing Fuel Vapor Control Valve Tube Assembly (With ORVR Only)

    Disconnect fuel vapor valve from fuel vapor control valve tube. Plug hose on fuel vapor valve assembly and at fuel vapor control valve tube assembly. Move EVAP tester to fuel filler pipe. Pressurize system to 14 in. H2 O (3.48 kPa). If pressure drops immediately, perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform DRIVE CYCLE PROCEDURE under DIAGNOSTIC MONITORS in SELF-DIAGNOSTICS - EEC-V - GASOLINE & NGV article. Ensure PENDING CODE CHECK & EVAP MONITOR "BYPASS" CHECK is performed and go to next step. If pressure does not drop immediately, replace fuel vapor control valve tube assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform DRIVE CYCLE PROCEDURE under DIAGNOSTIC MONITORS in SELF-DIAGNOSTICS - EEC-V - GASOLINE & NGV article. Ensure PENDING CODE CHECK & EVAP MONITOR "BYPASS" CHECK is performed.

  6. Testing Fuel Vapor Valve Assembly

    Disconnect fuel vapor valve tube assembly at EVAP canister tube "T" fitting connector and at fuel vapor valve. Plug both open ports at tube assembly. Pressurize system to 14 in. H2 O (3.48 kPa). If pressure drops immediately, reconnect all components. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform DRIVE CYCLE PROCEDURE under DIAGNOSTIC MONITORS in SELF-DIAGNOSTICS - EEC-V - GASOLINE & NGV article. Ensure PENDING CODE CHECK & EVAP MONITOR "BYPASS" CHECK is performed. If pressure does not drop immediately, replace fuel vapor valve assembly. Perform evaporative emissions system leak test. See EVAPORATIVE EMISSIONS SYSTEM LEAK TEST . If system passes, perform DRIVE CYCLE PROCEDURE under DIAGNOSTIC MONITORS in SELF-DIAGNOSTICS - EEC-V - GASOLINE & NGV article. Ensure PENDING CODE CHECK & EVAP MONITOR "BYPASS" CHECK is performed.
scientia non olet · About LEMON Manuals