Front Seat-Back Cover Removal and Installation: Replacement

SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service.

• 1. Front Seat - Remove 
• 2. Subwoofer - Remove (With Subwoofer)
• 3. Front Seat-Back - Remove

  Courtesy of HONDA, U.S.A., INC.

  1. Release the straps (A) from the seat cushion frame springs (B), then pull back the undercover (C).

  Driver's seat - With DPMS  Courtesy of HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC. Driver's seat - With 8 way power seat  Courtesy of HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC. Driver's seat - With manual height adjustable seat  Courtesy of HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC. Passenger's seat - Without subwoofer  Courtesy of HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC. Passenger's seat - With subwoofer  Courtesy of HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.HONDA, U.S.A., INC.

  2. Disconnect the connector (A), and detach the connector clip(s) (B) 3. With power seat: Disconnect the connectors (C) 4. With DPMS: Disconnect the connectors (D) 5. With seat heater: Disconnect the connector(s) (E), and detach the connector clip (F) 6. With seat position sensor: Disconnect the connector (G) 7. Detach the harness clips (H) 8. Pry up the hooks (J) of the harness holders (K), then release them from the seat cushion frame springs (L).

  Courtesy of HONDA, U.S.A., INC.

  9. Release the hook strip (A) 10. Unzip the seat-back cover (B).

  Courtesy of HONDA, U.S.A., INC.

  11. Detach the hook and loop fasteners (A) 12. Release the hook strips (B), and loosen the seat-back cover (C).

  Courtesy of HONDA, U.S.A., INC.

  13. Detach the harness clip (A) 14. Pull out the harness (B) through the holes (C) in the seat-back cover (D).

  Courtesy of HONDA, U.S.A., INC.

  15. Release airbag attachment wires A and B from the seat-back frame (C).

  Courtesy of HONDA, U.S.A., INC.

  16. Release the hook strips (A) from the seat-back frame (B).

• 4. Head Restraint Guides - Remove

  Courtesy of HONDA, U.S.A., INC.

• 5. Front Seat-Back Cover/Pad - Remove

  Courtesy of HONDA, U.S.A., INC.

• 6. Front Seat-Back Cover - Remove

  Courtesy of HONDA, U.S.A., INC.

  1. Remove airbag attachment wires A and B.

  Courtesy of HONDA, U.S.A., INC.

  2. Remove the upholstery rings (A), then remove the front seat-back cover (B).

• 7. All Removed Parts - Install

  Courtesy of HONDA, U.S.A., INC.

  Courtesy of HONDA, U.S.A., INC.

  1. Install the parts in the reverse order of removal.

  NOTE: 

  • Reinstall airbag attachment wires A and B securely to the front seat-back frame (C) as shown.
  • Replace all of the upholstery rings (D) fastening the seat-back (E) to the pad wires (F) with new ones using commercially available upholstery ring pliers (G).