LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Honda >> 2016 >> CR-V EX, Eng CD K24W9, FWD >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Technical Service Bulletins >> Other Variant >> Accessory Drive Belts >> Water Pump Seizes Or The Drive Belt Is Shredded (17-063)

Water Pump Seizes Or The Drive Belt Is Shredded (17-063)

WARNING: This page is about the CR-V EX, Eng CD K24V1, which is a different variant/trim than selected.
Publication date: 2017-09-15
Reference number: 17-063

WATER PUMP SEIZES OR THE DRIVE BELT IS SHREDDED

WATER PUMP SEIZES OR THE DRIVE BELT IS SHREDDED

TECHNICAL SERVICE BULLETIN

Reference Number(s): 17-063 Version 1, Date of Issue:  September 15, 2017
HONDA: 2013-16 Accord, CR-V

AFFECTED VEHICLES

AFFECTED VEHICLES

Year Model Trim VIN Range
2013-16 Accord L4 Only ALL
2013-16 CR-V ALL ALL

SYMPTOM

The water pump seized or the drive belt shredded.

POSSIBLE CAUSES

The water pump bearing is out of specification.

CORRECTIVE ACTION

Replace the water pump and drive belt if damaged.

REQUIRED MATERIALS

PARTS INFORMATION

Part Name Part Number Quantity
Honda Genuine Antifreeze/Coolant Type 2 OL999-9011 1

PARTS INFORMATION

PARTS INFORMATION

Part Name Part Number Quantity
Water Pump (2013-14 CR-V) 19200-R5A-A01 1
Water Pump (2015-16 CR-V, 2013-16 Accord) 19200-5A2-A01 1
Drive Belt (Accord with CVT) 31110-5A2-A01 1
Drive Belt (Accord with manual transmission) 31110-5B0-Y01 1
Drive Belt (2013-14 CR-V) 31110-R5A-A01 1
Drive Belt (2015-16 CR-V) 31110-5LA-A02 1

WARRANTY CLAIM INFORMATION

The normal warranty applies.

WARRANTY CLAIM INFORMATION

Operation Number Description Flat Rate Time Defect Code Symptom Code Template ID Failed Part Number
113100 2013-16 Accord (All): Replace the water pump only. 1.4 hrs 02301 03217 A17063A 19200-5A2-A01
113100 2013-16 Accord (CVT): Replace the water pump and drive belt (if necessary). 1.4 hrs 02301 03217 A17063B 19200-5A2-A01
113100 2013-16 Accord M/T): Replace the water pump and drive belt (if necessary). 1.4 hrs 02301 03217 A17063C 19200-5A2-A01
113100 2013-14 CR-V: Replace the water pump only. 1.8 hrs 02301 03217 A17063D 19200-5A2-A01
113100 2013-14 CR-V: Replace the water pump and drive belt (if necessary). 1.8 hrs 02301 03217 A17063E 19200-5A2-A01
113100 2015-16 CR-V: Replace the water pump only. 1.7 hrs 02301 03217 A17063F 19200-5A2-A01
113100 2015-16 CR-V: Replace the water pump and drive belt (if necessary). 1.7 hrs 02301 03217 A17063G 19200-5A2-A01

Skill Level: Repair Technician

REPAIR PROCEDURE 2013-14 CR-V

  1. Raise the vehicle on a lift, and make sure it is securely supported.
  2. Remove the right front wheel.
  3. Remove the bolts, then remove the clips that secure the front inner fender and the front splash shield to the body.
    G11664746
  4. From under the front bumper, remove the clips.
  5. From under the body, remove the clips, then pull out the front splash shield.
  6. Loosen the drain plug, and drain the coolant.
  7. After the coolant has drained, tighten the drain plug securely.
  8. Move the coolant reservoir.
  9. Remove the coolant reservoir tank bracket.
    G11664747
  10. Move the auto-tensioner using the belt tension release tool in the direction of the arrow to relieve tension from the drive belt, then remove the drive belt.
    G11664748
  11. Remove the idler pulley base.
    G11664749
  12. Remove the auto-tensioner.
    G11664750
  13. Hold the pulley with the holder handle and the crankshaft pulley holder.
    G11664751
  14. Remove the bolt with a socket and a breaker bar, then remove the crankshaft pulley.
  15. Remove the water pump.
    G11664752
  16. Inspect and clean the mating surface of the engine block.
  17. Install the water pump with a new O-ring, then torque the bolts to 12 N.m (9 lb-ft)  .
    G11664753
  18. Clean the crankshaft pulley, the crankshaft, the bolt, and the washer. Lubricate with new engine oil as shown.
    G11664754
  19. Install the crankshaft pulley, then hold the pulley with the holder handle and the crankshaft pulley holder.
    G11664755
  20. Torque the bolt to 50 N.m (37 lb-ft)  with a torque wrench and a 19mm socket. Do not use an impact wrench.
    NOTE: If the pulley bolt or crankshaft are new, torque the bolt to 177 N.m (131 lb-ft)  , then remove the bolt, and torque it to 50 N.m (37 lb-ft)  .
  21. Tighten the pulley bolt an additional 90°.
  22. Install the auto-tensioner, and torque the bolts to 22 N.m (16 lb-ft)  .
    G11664756
  23. Install the idler pulley base, and torque the bolts to 12 N.m (9 lb-ft)  .
    G11664757
  24. Install the coolant reservoir tank bracket, and torque the bolts to 9.4 N.m (6.9 lb-ft)  .
    G11664758
  25. Install the coolant reservoir and the drive belt.
  26. Install the front splash shield.
  27. Install the wheel, and torque the nuts to 108 N.m (80 lb-ft)  .
  28. Fill the engine with coolant.

REPAIR PROCEDURE 2013-16 ACCORD, 2015-16 CR-V

NOTE: This procedure is in an outline form. For more information, see the service information.
  1. Drain the engine coolant.
  2. Disconnect the 12-volt battery terminal (if required).
  3. Remove the drive belt.
  4. Remove the drive belt auto tensioner.
  5. Remove the alternator (if required).
  6. Remove the water pump.
    G11664759
  7. Install the new water pump, and torque the bolts to 12 N.m (9 lb-ft)  .
  8. Install the alternator, and torque the bolts to 45 N.m (33 lb-ft)  (if required).
  9. Install all remaining parts in the reverse order of removal.
  10. Fill the engine coolant.

END

scientia non olet · About LEMON Manuals