Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read HVAC DTCs and record on the repair order.
2. Record the Environmental Data.
3. With the scan tool, erase DTCs.
4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read HVAC DTCs.
  Did the DTC return?
  
  Yes
  - Go To 3
  No
  - Go To 2
PERFORM HVAC ACTUATOR CALIBRATION TEST
1. With the scan tool, perform the HVAC Actuator Calibration Test.
  Did this DTC change from Stored to Active while performing the HVAC Actuator Calibration Test?
  
  Yes
  - Go To 5
  No
  - Go To 3
CHECK THE HARNESS CONNECTORS FOR PROPER CONNECTION
1. Check for loose, damaged or corroded connections on the Right Mode Door Actuator harness connector and HVAC Module harness connector.
  Are there any loose or damaged connectors?
  
  Yes
  - Repair the harness connectors as necessary.
  No
  - Go to Step 4.
CHECK THE (C65) RIGHT MODE DOOR DRIVER 1 CIRCUIT FOR A SHORT TO BATTERY
1. Turn the Ignition off.
2. Disconnect the Right Mode Door Actuator harness connector.
3. Disconnect the HVAC Module harness connector.
4. Turn the Ignition on.
5. Using a multimeter, check for voltage in the (C65) Right Mode Door Driver 1 circuit between pin 5 of the Right Mode Door Actuator harness connector and pin 16 of the HVAC Module harness connector.
  Is there a short circuit to voltage in the (C65) Right Mode Door Driver 1 circuit?
  
  Yes
  - Repair the (C65) Right Mode Door Driver 1 circuit for a short to battery.
  No
  - Go To 5
CHECK THE RIGHT MODE DOOR ACTUATOR FOR PROPER OPERATION
1. Replace the Right Mode Door Actuator in accordance with the Service Information. Refer to ACTUATOR, MODE DOOR, REMOVAL AND INSTALLATION .
2. With the scan tool, erase HVAC DTCs and perform the HVAC Actuator Calibration Test.
  Did this DTC reset?
  
  Yes
  - Go To 6
  No
  - Test complete.
  - Perform the HVAC VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all HVAC Module harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all HVAC Module harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read HVAC Module DTCs.
  Did the DTC return?
  
  Yes
  - Replace the HVAC Module in accordance with the Service information. Refer to MODULE, HVAC, REMOVAL AND INSTALLATION .
  - Perform the HVAC VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Repair any faulty connections.
  - Perform the HVAC VERIFICATION TEST. Refer to STANDARD PROCEDURE .