Diagnostic Test

CHECK FOR AN ACTIVE DTC
NOTE:
Verify that the vehicle's battery is fully charged with a DVOM and use the scan tool to compare the Battery Voltage listed under "Data" in the RFH View to that of the BCM. If the vehicle's battery is not fully charged, correct this condition before proceeding.

NOTE:
To Turn the ignition on, place the FOBIK in the center console and press the Stop/Start button.
1. Press the ignition on.
2. With the scan tool, read RF Hub DTCs and record on the repair order.
3. With the scan tool, erase DTCs.
4. With the scan tool, read RF Hub DTCs.
  Is the DTC active?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE (D920) PASSIVE ENTRY ANTENNA 1 SIGNAL CIRCUIT FOR AN OPEN
1. Disconnect the Passive Entry Antenna 1 harness connector.
2. Measure the resistance of the (D920) Passive Entry Antenna 1 Signal circuit between the RF HUB C2 connector and the Passive Entry Antenna 1 connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 3
  No
  - Repair the (D920) Passive Entry Antenna 1 Signal circuit for an open.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE (D921) PASSIVE ENTRY ANTENNA 1 RETURN CIRCUIT FOR AN OPEN
1. Measure the resistance of the (D921) Passive Entry Antenna 1 Return circuit between the RF HUB C2 connector and the Passive Entry Antenna 1 connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 4
  No
  - Repair the (D921) Passive Entry Antenna 1 Return circuit for an open.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE (D920) PASSIVE ENTRY ANTENNA 1 SIGNAL CIRCUIT FOR A SHORT TO THE (D921) PASSIVE ENTRY ANTENNA 1 RETURN CIRCUIT
1. Check for continuity between the (D920) Passive Entry Antenna 1 Signal circuit and the (D921) Passive Entry Antenna 1 Return circuit at the RF Hub C2 harness connector.
  Is there continuity between the (D920) Passive Entry Antenna 1 Signal circuit and the (D921) Passive Entry Antenna 1 Return circuit?
  
  Yes
  - Repair the (D920) Passive Entry Antenna 1 Signal circuit for a short to the (D921) Passive Entry Antenna 1 Return circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Replace the Passive Entry Antenna in accordance with the Service Information. Refer to ANTENNA, PASSIVE ENTRY, REMOVAL AND INSTALLATION .
  - Go To 5
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all RF Hub harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all RF Hub Module harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Vehicle Scan Report, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read RF Hub DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Radio Frequency Hub (RF Hub) in accordance with the Service Information. Refer to MODULE, RADIO FREQUENCY (RF HUB), REMOVAL AND INSTALLATION .
  - Perform the RADIO FREQUENCY HUB VERIFICATION TEST. Refer to RADIO FREQUENCY HUB (RF HUB) VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.