Diagnostic Test

CHECK FOR AN ACTIVE DTC
WARNING:
When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
1. With the scan tool, read Body Control Module (BCM) DTCs and record on the repair order.
2. Record the Environmental Data.
3. With the scan tool, erase DTCs.
4. Attempt to crank the engine.
5. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR INTERMITTENT CONDITIONS procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE STARTER RELAY
1. Turn the ignition off.
2. Remove the Starter Relay from the Auxiliary Power Distribution Center (PDC) Assembly and substitute it with a known good relay.
  WARNING:
  When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing. Failure to follow these instructions may result in possible serious or fatal injury.
3. With the scan tool, erase DTCs.
4. Attempt to crank the engine.
5. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 3
  No
  - Replace the Starter Relay.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE (F30) STARTER RELAY CONTROL CIRCUIT FOR AN OPEN
1. Turn the ignition off.
2. Remove the Starter Relay from the Auxiliary PDC Assembly.
3. Disconnect the BCM C3/C harness connector.
4. Measure the resistance of the (F30) Starter Relay Control circuit between the Starter Relay - terminal 30 in the Auxiliary PDC Assembly and BCM C3/C harness connector - terminal 1.
  Is the resistance above 3.0 Ohms?
  
  Yes
  - Repair the open in the (F30) Starter Relay Control circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 4
CHECK THE AUXILIARY PDC ASSEMBLY
1. Disconnect the Auxiliary PDC Assembly C2 harness connector.
2. Measure the resistance of the (F30) Starter Relay Control circuit between the Auxiliary PDC Assembly C2 harness connector and the Starter Relay - terminal 30 in the Auxiliary PDC Assembly.
  Is the resistance above 3.0 Ohms?
  
  Yes
  - Check the Auxiliary PDC Assembly connectors for signs of water intrusion, corrosion, pushed out or bent terminals and correct pin tension. If no problems are found, replace the Auxiliary Power Distribution Center (PDC) Assembly in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 5
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all BCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all BCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Body Control Module (BCM) in accordance with the Service Information. Refer to MODULE, BODY CONTROL (BCM), REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.