Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read Body Control Module (BCM) DTCs and record on the repair order.
2. Record the Environmental Data and any DTCs.
3. With the scan tool, erase DTCs.
4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer TESTING FOR AN INTERMITTENT CONDITION to STANDARD PROCEDURE .
CHECK THE (P372) DOOR LOCK SW RTN PASS CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition off.
2. Disconnect the Passenger Interior Door Handle Switch harness connector.
3. Turn the ignition on.
4. Measure the voltage on the (P372) Door Lock Sw Rtn Pass circuit at the Passenger Interior Door Handle Switch harness connector.
  Is there any voltage present?
  
  Yes
  - Repair the short to voltage on the (P372) Door Lock Sw Rtn Pass circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 3
CHECK THE BCM FOR PROPER OPERATION
1. Turn the ignition off.
2. Connect a fused jumper wire between ground and the (P372) Door Lock Sw Rtn Pass circuit at the Passenger Interior Door Handle Switch harness connector.
3. Turn the ignition on.
4. With the scan tool, read BCM DTCs.
  Does DTC: B107D-23-PASSENGER FRONT DOORS-SIGNAL STUCK LOW set as active?
  
  Yes
  - Replace the Passenger Interior Door Handle Switch in accordance with the service information. Refer to SWITCH, LOCK, REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 4
CHECK THE (P372) DOOR LOCK SW RTN PASS CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Turn the ignition off.
2. Disconnect the BCM C6/F harness connector.
3. Measure the resistance on the (P372) Door Lock Sw Rtn Pass circuit between the Passenger Interior Door Handle Switch harness connector and BCM C6/F harness connector - terminal 6.
  Is the resistance above 3.0?
  
  Yes
  - Repair the open or high resistance on the (P372) Door Lock Sw Rtn Pass circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 5
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all BCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Connect all BCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Body Control Module (BCM) in accordance with the Service Information. Refer to MODULE, BODY CONTROL (BCM), REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.