Diagnostic Test

CHECK FOR ANY SERVICE BULLETINS OR PCM SOFTWARE UPDATES
1. Check for any applicable Service Bulletins or Flash updates related to the DTC.
  Are there any applicable Service Bulletins or Flash updates?
  
  Yes
  - Perform the applicable repair.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 2
CHECK FOR OTHER DTCS
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
  Are there any 5-Volt Sensor Reference Voltage or Manifold Absolute Pressure Sensor Low or High DTCs also present?
  
  Yes
  - Perform the applicable diagnostic procedure(s). Refer to 2.0L - DIAGNOSTIC CODE INDEX .
  No
  - Go To 3
READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
1. With the scan tool, erase all DTCs.
2. Turn the ignition off for a minimum of 10.0 seconds.
3. Turn the ignition on.
4. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 4
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK THE (F855) 5-VOLT SUPPLY CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Turn the ignition off.
2. Disconnect the MAP Sensor harness connector.
3. Turn the ignition on.
4. Measure the voltage on the (F855) 5-Volt Supply circuit at the MAP Sensor harness connector.
  Is the voltage above 4.9 volts?
  
  Yes
  - Go To 5
  No
  - Repair the (F855) 5-Volt Supply circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK THE (K1) MAP SENSOR SIGNAL CIRCUIT FOR HIGH RESISTANCE
1. Turn the ignition off.
2. Disconnect the PCM C2 harness connector.
3. Measure the resistance of the (K1) MAP Sensor Signal circuit between the MAP Sensor harness connector and the PCM C2 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 6
  No
  - Repair the (K1) MAP Sensor Signal circuit for high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK THE (K914) SENSOR GROUND CIRCUIT FOR HIGH RESISTANCE
1. Measure the resistance of the (K914) Sensor Ground circuit between the MAP Sensor harness connector and the PCM C2 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 7
  No
  - Repair the (K914) Sensor Ground circuit for high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
REPLACE MAP SENSOR AND RETEST FOR DTC
1. Replace the MAP Sensor in accordance with the Service Information.
2. Reconnect the PCM C2 harness connector.
3. Reconnect the MAP harness connector.
4. Using the recorded Freeze Frame Data and the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read PCM DTCs.
  Is the DTC active or pending?
  
  Yes
  - Go To 8
  No
  - Repair is complete.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK RELATED PCM AND COMPONENT CONNECTIONS
1. Perform any Service Bulletins that apply.
2. Disconnect all PCM harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
11. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Powertrain Control Module (PCM) in accordance with the Service information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  - Test complete.