Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read Body Control Module (BCM) DTCs and record on the repair order.
2. Record the Environmental Data and any DTCs.
3. With the scan tool, erase DTCs.
4. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
5. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE (Z332) GROUND CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Turn the ignition off.
2. Disconnect the Electronic Overhead Module harness connector.
3. Measure the resistance of the (Z332) Ground circuit between ground and the Electronic Overhead Module harness connector.
  Is the resistance above 3.0 Ohms?
  
  Yes
  - Repair the open or high resistance on the (Z332) Ground circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (M1) COURTESY LAMPS DRIVER CIRCUIT FOR CONTINUITY TO GROUND
1. Check for continuity between the (Z332) Ground circuit and (M1) Courtesy Lamps Driver circuit at the Electronic Overhead Module harness connector.
  Is there continuity between the (Z332) Ground circuit and (M1) Courtesy Lamps Driver circuit?
  
  Yes
  - Go To 5
  No
  - Go To 4
CHECK THE BCM FOR PROPER OPERATION
1. Turn the ignition on.
2. Connect a fused jumper wire between 12 volts and the (M1) Courtesy Lamps Driver circuit at the Electronic Overhead Module harness connector.
3. With the scan tool, read BCM DTCs.
  Is DTC: B1060-12 - FRONT CEILING LIGHT POWER SUPPLY - CIRCUIT SHORT TO BATTERY set as Active?
  
  Yes
  - Replace the Electronic Overhead Module in accordance with the Service Information. Refer to LAMP, DOME, REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 6
CHECK THE (M1) COURTESY LAMPS DRIVER CIRCUIT FOR CONTINUITY TO GROUND
1. Disconnect the BCM C5/E harness connector.
2. Check for continuity between ground and the (M1) Courtesy Lamps Driver circuit at the Electronic Overhead Module harness connector.
  Is there continuity between ground and the (M1) Courtesy Lamps Driver circuit?
  
  Yes
  - Repair the short to ground on the (M1) Courtesy Lamps Driver circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 7
CHECK THE (M1) COURTESY LAMPS DRIVER CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Measure the resistance on the (M1) Courtesy Lamps Driver circuit between the Electronic Overhead Module harness connector and BCM C5/E harness connector - terminal 6.
  Is the resistance above 3.0 Ohms?
  
  Yes
  - Repair the open or high resistance on the (M1) Courtesy Lamps Driver circuit.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 7
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all BCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all BCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read BCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Body Control Module (BCM) in accordance with the Service Information. Refer to MODULE, BODY CONTROL (BCM), REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.