Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read Torque Vectoring Module (TVM) DTCs and record on the repair order.
2. With the scan tool, erase TVM DTCs.
3. Turn the ignition off for ten seconds.
4. Using the recorded information along with the When Monitored and Set Conditions, operate the vehicle within the conditions that set the DTC.
5. With the scan tool, read TVM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE (T430) LEFT TORQUE MOTOR U SIGNAL CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the TVM 18 pin connector.
3. Disconnect the Left Torque Motor connector.
4. Check the continuity between ground and the (T430) Left Torque Motor U Signal circuit.
  Is there continuity between ground and the (T430) Left Torque Motor U Signal circuit?
  
  Yes
  - Repair the (T430) Left Torque Motor U Signal circuit for a short to ground.
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 3
CHECK THE (T431) LEFT TORQUE MOTOR W SIGNAL CIRCUIT FOR A SHORT TO GROUND
1. Check the continuity between ground and the (T431) Left Torque Motor W Signal circuit.
  Is there continuity between ground and the Signal circuit?
  
  Yes
  - Repair the (T431) Left Torque Motor W Signal circuit for a short to ground.
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 4
CHECK THE (T432) LEFT TORQUE MOTOR V SIGNAL CIRCUIT FOR A SHORT TO GROUND
1. Check the continuity between ground and the (T432) Left Torque Motor V Signal circuit.
  Is there continuity between ground and the (T432) Left Torque Motor V Signal circuit?
  
  Yes
  - Repair the (T432) Left Torque Motor V Signal circuit for a short to ground.
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 5
CHECK THE (T430) LEFT TORQUE MOTOR U SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition on.
2. Measure the voltage of the (T430) Left Torque Motor U Signal circuit.
  Is there any voltage present?
  
  Yes
  - Repair the (T430) Left Torque Motor U Signal circuit for a short to voltage.
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 6
CHECK THE (T431) LEFT TORQUE MOTOR W SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE
1. Measure the voltage of the (T431) Left Torque Motor W Signal circuit.
  Is there any voltage present?
  
  Yes
  - Repair the (T431) Left Torque Motor W Signal circuit for a short to voltage.
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 7
CHECK THE (T432) LEFT TORQUE MOTOR V SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE
1. Measure the voltage of the (T432) Left Torque Motor V Signal circuit.
  Is there any voltage present?
  
  Yes
  - Repair the (T432) Left Torque Motor V Signal circuit for a short to voltage.
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 8
CHECK FOR A SHORT BETWEEN THE LEFT TORQUE MOTOR SIGNAL CIRCUITS
1. Turn the ignition off.
2. Check for continuity between the (T430) Left Torque Motor U Signal circuit and the (T431) Left Torque Motor W Signal circuit.
3. Check for continuity between the (T430) Left Torque Motor U Signal circuit and the (T432) Left Torque Motor V Signal circuit.
4. Check for continuity between the (T431) Left Torque Motor W Signal circuit and the (T432) Left Torque Motor V Signal circuit.
  Is there continuity between any of the Signal circuits?
  
  Yes
  - Repair the short between the Left Torque Motor Signal circuits.
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Go To 9
CHECK RELATED WIRING AND HARNESS CONNECTIONS
1. Turn the ignition off.
2. Check the related component and module power supply and ground circuits.
3. Disconnect the TVM harness connector(s).
4. Disconnect all related in-line harness connections (if equipped).
5. Disconnect the related component harness connectors.
6. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
7. Reconnect all harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
10. With the scan tool, erase DTCs.
11. Using the recorded information along with the When Monitored and Set Conditions, operate the vehicle within the conditions that set the DTC.
12. With the scan tool, read TVM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 10
  No
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  - Test complete.
CHECK DTCS AFTER REPLACING THE LEFT TORQUE MOTOR
1. Turn the ignition off.
2. Replace the Left Torque Motor in accordance with the Service Information.
3. Turn the ignition on.
4. With the scan tool, erase TVM DTCs.
5. Using the recorded information along with the When Monitored and Set Conditions, operate the vehicle within the conditions that set the DTC.
6. With the scan tool, read TVM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the TVM in accordance with the Service Information.
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Perform the TVM VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  - Test Complete.