Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read Powertrain Control Module 2 (PCM-2) DTCs and Freeze Frame Data and record on the repair order.
2. Using the recorded Freeze Frame Data and the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
3. With the scan tool, read PCM-2 DTCs.
  Is the DTC active or pending?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION. Refer to STANDARD PROCEDURE .
CHECK THE (K58) INJECTOR 6 CONTROL CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT
1. Turn the ignition off.
2. Disconnect the PCM-2 C2 harness connector.
3. Disconnect the Fuel Injector 6 harness connector.
4. Check for continuity between the (K58) Injector 6 Control circuit and all other circuits at the PCM-2 C2 harness connector.
  Is there continuity between the (K58) Injector 6 Control circuit and any other circuit?
  
  Yes
  - Repair the (K58) Injector 6 Control circuit for a short to the circuit that showed continuity.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (K658) INJECTOR 6 LOW SIDE CONTROL CIRCUIT FOR A SHORT TO ANOTHER CIRCUIT
1. Check for continuity between the (K658) Injector 6 Low Side Control circuit and all other circuits at the PCM-2 C2 harness connector.
  Is there continuity between the (K658) Injector 2 Low Side Control circuit and any other circuit?
  
  Yes
  - Repair the (K658) Injector 6 Low Side Control circuit for a short to the circuit that showed continuity.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
CHECK THE FUEL INJECTOR 6 RESISTANCE
1. Measure the resistance of Fuel Injector 6.
  NOTE:
  Compare the resistance to other known good injectors on the vehicle.
  
  Is the resistance of the Fuel Injector 6 within 10% of the other known good injectors?
  
  Yes
  - Go To 5
  No
  - Replace the Fuel Injector in accordance with the Service Information. Refer to INJECTOR(S), FUEL, REMOVAL AND INSTALLATION .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK RELATED PCM AND COMPONENT CONNECTIONS
1. Perform any Service Bulletins that apply.
2. Disconnect all PCM-2 harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all PCM-2 harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
11. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Powertrain Control Module 2 (PCM-2) in accordance with the Service information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  - Test complete.