Diagnostic Test

CHECK FOR AN ACTIVE DTC
NOTE:
If there are any 5-Volt Supply DTCs present, perform the diagnostics for those DTCs before continuing with this one.
1. Turn the ignition on.
2. With the scan tool, read DTCs and record on the repair order.
  Is the DTC active or pending?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK THE (K926) CRANKCASE PRESSURE SENSOR SIGNAL CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Disconnect the Crankcase Pressure Sensor harness connector.
3. Disconnect the PCM C2 harness connector.
4. Check for continuity between ground and the (K926) Crankcase Pressure Sensor Signal circuit at the Crankcase Pressure Sensor harness connector.
  Is there continuity between ground and the (K926) Crankcase Pressure Sensor Signal circuit?
  
  Yes
  - Repair the (K926) Crankcase Pressure Sensor Signal circuit for a short to ground.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (K926) CRANKCASE PRESSURE SENSOR SIGNAL CIRCUIT FOR A SHORT TO THE (K916) SENSOR GROUND CIRCUIT
1. Check for continuity between the (K926) Crankcase Pressure Sensor Signal circuit and the (K916) Sensor Ground circuit at the Crankcase Pressure Sensor harness connector.
  Is there continuity between the (K926) Crankcase Pressure Sensor Signal circuit and the (K916) Sensor Ground circuit?
  
  Yes
  - Repair the (K926) Crankcase Pressure Sensor Signal circuit for a short to the (K916) Sensor Ground circuit.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 4
CRANKCASE PRESSURE SENSOR
1. Reconnect the PCM C2 harness connector.
2. Connect a jumper between the (K926) Crankcase Pressure Sensor Signal circuit and the (F853) 5-Volt Supply circuit.
3. Turn the ignition on.
  NOTE:
  The scan tool should display the DTC P051D-CRANKCASE PRESSURE SENSOR CIRCUIT HIGH as active or pending with the jumper in place.
4. With the scan tool, read DTCs and record on the repair order.
  Does the DTC display as described above?
  
  Yes
  - Replace the Crankcase Pressure Sensor in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 5
CHECK RELATED PCM AND COMPONENT CONNECTIONS
1. Disconnect all PCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
5. Connect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
10. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - The wiring or poor connection problem has been repaired.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .