Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read Comfort Seat Wheel Module (CSWM) DTCs and record on the repair order.
2. With the scan tool, erase CSWM DTCs.
3. Turn the ignition off for ten seconds.
4. Turn the ignition on.
5. Turn the Passenger Seat Heater on.
6. With the scan tool, read CSWM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE (P688) PASSENGER FRONT HEATED SEAT TEMP SENSE CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Turn the ignition off.
2. Disconnect the CSWM connector(s).
3. Disconnect the Passenger Seat Heater harness connector(s).
4. Measure the resistance of the (P688) Passenger Front Heated Seat Temp Sense circuit between the Passenger Seat Heater connector and the CSWM connector.
  Is the resistance above 2.0 Ohms?
  
  Yes
  - Repair the (P688) Passenger Front Heated Seat Temp Sense circuit for an open or high resistance.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (P968) HEATED SEAT SENSOR RETURN CIRCUIT FOR AN OPEN OR HIGH RESISTANCE
1. Measure the resistance of the (P968) Heated Seat Sensor Return circuit between the Passenger Seat Heater connector and the CSWM connector.
  Is the resistance above 2.0 Ohms?
  
  Yes
  - Repair the (P968) Heated Seat Sensor Return circuit for an open or high resistance.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 4
CHECK THE (P688) PASSENGER FRONT HEATED SEAT TEMP SENSE CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition on.
2. Measure the voltage of the (P688) Passenger Front Heated Seat Temp Sense circuit.
  Is there any voltage present?
  
  Yes
  - Repair the (P688) Passenger Front Heated Seat Temp Sense circuit for a short to voltage.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 5
CHECK THE (P688) PASSENGER FRONT HEATED SEAT TEMP SENSE CIRCUIT FOR A SHORT TO GROUND
1. Turn the ignition off.
2. Check the continuity between ground and the (P688) Passenger Front Heated Seat Temp Sense circuit.
  Is there continuity between ground and the (P688) Passenger Front Heated Seat Temp Sense circuit?
  
  Yes
  - Repair the (P688) Passenger Front Heated Seat Temp Sense circuit for a short to ground.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Go To 6
CHECK DTCS AFTER REPLACING PASSENGER SEAT HEATER
1. Turn the ignition off.
2. Replace the Passenger Seat Heater in accordance with the Service Information. Refer to PAD, HEATER, REMOVAL AND INSTALLATION .
3. Turn the ignition on.
4. With the scan tool, erase CSWM DTCs.
5. Turn the ignition off for ten seconds.
6. Turn the ignition on.
7. Turn the Passenger Seat Heater on.
8. With the scan tool, read CSWM DTCs.
  Did the DTC return?
  
  Yes
  - Go To 7
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all CSWM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded information along with the When Monitored and Set Conditions, operate the vehicle within the conditions that set the DTC.
10. With the scan tool, read CSWM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the CSWM in accordance with the Service Information. Refer to MODULE, COMFORT SEAT AND WHEEL (CSWM), REMOVAL AND INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.