Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

CHECK FOR AN ACTIVE DTC
1. With the scan tool, read Powertrain Control Module 2 (PCM-2) DTCs and Freeze Frame Data and record on the repair order.
2. Using the recorded Freeze Frame Data and the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
3. With the scan tool, read DTCs.
  Is the DTC active or pending?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
CHECK FOR OTHER DTCS
1. Refer to the recorded DTCs.
  Are there any Boost Pressure Sensor 2 circuit faults or Bank 2 MAP Sensor DTCs active or pending?
  
  Yes
  - Perform the applicable diagnostic procedure(s). Refer to DTC INDEX .
  No
  - Go To 2
CHECK THE AIR INTAKE SYSTEM AND INTAKE MANIFOLD FOR LEAKS
1. Visually inspect for leaks or damage to the intake air supply plumbing.
2. Check for vacuum leaks at the Intake Manifold.
  Are there any leaks or damage to the intake air supply plumbing or Intake Manifold?
  
  Yes
  - Perform the appropriate repairs.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Go To 3
CHECK THE (F855) 5-VOLT SUPPLY CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Turn the ignition off.
2. Disconnect the Boost Pressure Sensor 2 harness connector.
3. Disconnect the PCM-2 C2 harness connector.
4. Measure the resistance of the (K855) 5-Volt Supply circuit between the Boost Pressure Sensor 2 harness connector and the PCM-2 C2 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 4
  No
  - Repair the (K855) 5-Volt Supply circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST.
CHECK THE (K383) BOOST PRESSURE 2 SIGNAL CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Measure the resistance of the (K383) Boost Pressure 2 Signal circuit between the Boost Pressure Sensor 2 harness connector and the PCM-2 C2 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Repair the (K383) Boost Pressure 2 Signal circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST.
  No
  - Go To 5
CHECK THE (K900) SENSOR GROUND CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Turn the ignition off.
2. Measure the resistance of the (K900) Sensor Ground circuit between the Boost Pressure Sensor harness connector and the PCM-2 C2 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 6
  No
  - Repair the (K900) Sensor Ground circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
INSTALL A NEW BOOST PRESSURE SENSOR AND RETEST FOR DTC
1. Install a new Boost Pressure Sensor 2 in accordance with the service information. Refer to SENSOR, TURBO BOOST PRESSURE, REMOVAL AND INSTALLATION .
2. Reconnect the PCM-2 C2 harness connector.
3. Turn the ignition on.
4. With the scan tool, erase DTCs.
5. Turn the ignition off.
6. Disconnect the Boost Pressure Sensor 2 harness connector.
7. Turn the ignition on.
8. Test drive or operate the vehicle in accordance with the When Monitored and Set Conditions.
  Did the DTC return?
  
  Yes
  - Go To 7
  No
  - Repair is complete.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
CHECK RELATED PCM-2 AND COMPONENT CONNECTIONS
1. Perform any Service Bulletins that apply.
2. Disconnect all PCM-2 harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all PCM-2 harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
11. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Powertrain Control Module 2 (PCM-2) in accordance with the Service information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  No
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
  - Test complete.